{"product_id":"miller-wired-foot-control","title":"MILLER WIRED FOOT CONTROL","description":"\u003ch4 dir=\"ltr\"\u003e\u003cstrong\u003eMiller RFCS-14 HD Heavy Duty Wired Foot Control – 14-Pin, 6m \u003c\/strong\u003e\u003c\/h4\u003e\r\n\u003cp dir=\"ltr\"\u003eThe Miller RFCS-14 HD is a heavy-duty wired foot pedal that gives TIG welders hands-free control of amperage and arc start\/stop (contactor) on Miller power sources with a 14-pin remote socket. It has a wider, heavier base and a thicker 6m cord than a standard pedal, so it stays put on the workshop floor and handles daily fabrication use.\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eBuilt for the workshop floor\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003eFoot controls often fail because they slide around, tip over, or the cord gets damaged where it leaves the pedal. The RFCS-14 HD's larger base and heavier cord give it more stability and a longer service life than a standard pedal. The cord can also be rerouted to exit the front, back or either side of the pedal. You can set it up to suit a left- or right-side bench layout, or angle it away from spatter and foot traffic. \u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003eChanging the cord exit is a simple job. You turn the pedal over, take off the bottom plate, move the cord to the slot you want, slide the strain relief into place and screw it back down. \u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003eFor TIG work, the pedal lets you ramp current up and down during the weld, fill craters as you finish, and control heat input on thin or heat-sensitive material, all without taking your hands off the torch and filler rod. A heel rest keeps your foot in a consistent position, which helps with comfort on long runs. \u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cdiv dir=\"ltr\"\u003e\r\n\u003ctable\u003e\r\n\u003cthead\u003e\r\n\u003ctr\u003e\r\n\u003cth scope=\"col\"\u003eSpecification\u003c\/th\u003e\r\n\u003cth scope=\"col\"\u003eDetail\u003c\/th\u003e\r\n\u003c\/tr\u003e\r\n\u003c\/thead\u003e\r\n\u003ctbody\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003eBrand\u003c\/td\u003e\r\n\u003ctd\u003eMiller (distributed in Australia by WIA)\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003eModel\u003c\/td\u003e\r\n\u003ctd\u003eRFCS-14 HD\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003ePart number\u003c\/td\u003e\r\n\u003ctd\u003eMR301589 (Miller 301589)\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003eControl type\u003c\/td\u003e\r\n\u003ctd\u003eWired foot control: remote amperage + contactor\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003eConnector\u003c\/td\u003e\r\n\u003ctd\u003e14-pin plug\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003eCord length\u003c\/td\u003e\r\n\u003ctd\u003e6m (20 ft), heavy-duty\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003eCord exit\u003c\/td\u003e\r\n\u003ctd\u003eReconfigurable: front, back, left or right\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003ctr\u003e\r\n\u003ctd\u003eSupersedes\u003c\/td\u003e\r\n\u003ctd\u003eMiller 194744 RFCS-14 HD (direct replacement)\u003c\/td\u003e\r\n\u003c\/tr\u003e\r\n\u003c\/tbody\u003e\r\n\u003c\/table\u003e\r\n\u003c\/div\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eCompatibility\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003eThis pedal suits Miller solid-state power sources with a 14-pin receptacle built after serial number JK674521. Older Miller machines that don't have a 14-pin socket won't accept it. Miller specifically lists the Econotig and the original Syncrowave 250, 350, 351 and 500 as not compatible.\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003eCommon Miller TIG machines in the current Australian range include the Dynasty, Syncrowave and Maxstar series.\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eFrequently asked questions\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eDoes the Miller RFCS-14 HD come with the plug fitted?\u003c\/strong\u003e\u003cbr\u003e Yes. It ships with the 6m cord and 14-pin plug already fitted, so it's ready to connect to the machine.\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWhat is the difference between the RFCS-14 and the RFCS-14 HD?\u003c\/strong\u003e\u003cbr\u003e The HD version has a larger, heavier base and a thicker cord. It's more stable underfoot and holds up better in production and fabrication environments.\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eWill this foot pedal work on my Miller TIG welder?\u003c\/strong\u003e\u003cbr\u003e It works if your machine has a 14-pin remote receptacle and was built after serial JK674521. Check the front or rear panel for a round 14-pin socket, or call QWS with your model and serial number.\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eCan I change which side the cable comes out of the foot pedal?\u003c\/strong\u003e\u003cbr\u003e Yes. The cord can be moved to exit the front, back or either side by removing the bottom plate and relocating it. You don't need any special tools.\u003c\/p\u003e\r\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eIs MR301589 the same as Miller 194744?\u003c\/strong\u003e\u003cbr\u003e Yes. 301589 is the current part number and directly replaces the earlier 194744 RFCS-14 HD.\u003c\/p\u003e","brand":"Miller","offers":[{"title":"Default Title","offer_id":67674582646935,"sku":"MR301589","price":766.5,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0301\/8663\/5399\/files\/mr301589_0_ab6e9600-a2fd-4330-a736-48947512464b.jpg?v=1790559591","url":"https:\/\/www.weldingsupply.com.au\/products\/miller-wired-foot-control","provider":"QWS - Welding Supply Solutions","version":"1.0","type":"link"}